Possessing an installed water heater in the home gives you the allowance to live conveniently and comfortably. During rainy, cold, or snowy days, you possess the privilege to take a bath or shower with hot water. Some expensive clothes you have need hot water for washing and with the assistance of heaters, you will launder them without problems of hot water. However, you may find yourself in hot water when it comes time for a water heater replacement. There is no need of being worried when you come across a heater flood or leak as you will successfully replace the heater.
The first thing you need to do is to relax and act with speed. You need to find the circuit breaker box immediately. After finding the breaker, you need to turn it off immediately. Try getting off the water so that you do not risk electric current shocks. However, if the heater is functioning with gas, you have to turn the gas valve off. Therefore, you need to find a valve for the line of the cold water. This valve is usually on top of the heater. It is either marked as blue or gold in coloring. After finding the valve, switch it off immediately.
You need to find the valve and then empty the tank. Make sure that it is out of water completely. While the tank may be dissipating water, you may utilize the vacuum to clean the resulting mess. You will then have to uninstall the heater. Before doing water heater replacement, you will have to uninstall it by unhooking water supply pipes, the wiring, and other sections. Eliminate the piping. In the event the pipes have connections with unions, use pipe wrenches to take them apart. Unions are removable fittings. However, if these pipes do not have unions, you will require a hacksaw. While using an old water heater, you need to do it with care to avoid accidents as water heater replacement is a complicated procedure.
After finishing uninstallation if the old water heater, you can start making plans for a new water heater replacement. You may choose to buy a new one or use the same one. Getting a good heater depends on the capacity of the heater to provide the demanded water heater. The variety of the tankless water heater is always the most eco-friendly and safe heater. In case you are opting for the tankless, you will have the advantage to enjoy unlimited water supply because this heater does not require a tank.
This heater keeps hot water in store until when you turn the faucet or shower on. You may have to use a very populous brand. It helps in cutting costs down and saving energy as it only supplies water when required. The right brand needs to have a life of at least twenty years. When you choose the right water heater, you have to carefully install it and obey the instructions of the installer.
In case you choose to install the tankless water heater while doing a water heater replacement, you will have to follow the instructions of the manufacturer. The installation of the tankless heater like the propane heater must be done well because it is complicated. You need to check the required connections for the right fitting.
While doing water heater replacement, do not try installing a water heater on the current outlet. The main reason is that the tankless water heater utilizes a large electricity amount to operate, therefore, it is crucial to supply it with an independent electrical line. You need to ensure that you get the tankless heater that will meet your needs adequately. You will have to choose from the current heater brands on the market. These brands come in diverse prices, sizes, and brands.
The most crucial factor you need to consider of checking on the capacity of the heater. You need to ensure that you know the number of gallons each heater will output. When you want to do water heater replacement and you are using more than one appliance that requires hot water at once, you will need a heater with a high GPM rate.
When you start water heater replacement for your heater, you need to be careful and cautious to prevent accidents from happening. You will have to start by cutting the power going to the breaker panel while working in the panel. After disconnecting the power, you will have to run the electric wire off the breaker panel from the location where the heater is installed. You will then install your breaker. You will connect electricity to the new heater and then install the required outlet. You will then remove the old heater before installing the new one. You can then test the new heater to make sure that the replaces the water heater is functional.
Here is a list of our services you can get at The Water Heater Guy:
FOR MORE INFO, CALL OR TEXT ANY OF OUR NUMBERS